Hoppa till innehåll
Free shipping over 3.000 DKK ex VAT! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%When temperatures are written down by hand, the measurement itself is rarely the weak linkWhen the Hole Is 500 mm Deep, the Measuring Instrument Has to Keep UpSee why the drain is blocked before you tear up the floor: a camera on five meters of cableWhen two hands measure the same bore differently: How three measuring points eliminate operator errorWhen the Bore Has to Be Measured Right: How a Self-Centering Three-Point Micrometer Removes Operator UncertaintyThree measuring points give a bore diameter that doesn’t depend on who is measuringWhen the multimeter shows 90 volts on a disconnected cable: how to tell ghost voltage from the real thingRead the tolerance in seconds when the micrometer shows the deviation directlySmall holes are rarely measured correctly with two points: how three contact points give you a diameter result you can trustYour measurement is never better than the surface you measure againstVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%When temperatures are written down by hand, the measurement itself is rarely the weak linkWhen the Hole Is 500 mm Deep, the Measuring Instrument Has to Keep UpSee why the drain is blocked before you tear up the floor: a camera on five meters of cableWhen two hands measure the same bore differently: How three measuring points eliminate operator errorWhen the Bore Has to Be Measured Right: How a Self-Centering Three-Point Micrometer Removes Operator UncertaintyThree measuring points give a bore diameter that doesn’t depend on who is measuringWhen the multimeter shows 90 volts on a disconnected cable: how to tell ghost voltage from the real thingRead the tolerance in seconds when the micrometer shows the deviation directlySmall holes are rarely measured correctly with two points: how three contact points give you a diameter result you can trustYour measurement is never better than the surface you measure against

Digital Point Micrometer 25-50 mm with 30° Conical Measuring Faces: When Ball Bearings, Thread Roots and Wire-Shaped Grooves Require Point Contact Instead of Flat

Published 12 July 2026 at 09:19

A toolmaker needs to measure the bottom of a thread in a shaft — between the thread crest (Ø 30 mm) and the thread’s actual root (Ø 27 mm). The requirement: verification of thread depth ±0.01 mm for correct matching with the corresponding internal thread.

With an ordinary micrometer with 6 mm flat anvil faces this is impossible — the anvil cannot reach DOWN into the 3 mm wide thread groove. A blade micrometer (which I wrote about for met-se earlier) works for parallel grooves but not for the thread with its V-shaped cross-section. What is needed: a micrometer with POINTED measuring faces that can penetrate all the way down into the V-groove and touch both side walls simultaneously.

A digital point micrometer with 30° conical measuring faces is exactly that instrument.

Point micrometer vs blade micrometer

The two specialty micrometer families are complementary:

Blade micrometer: Thin parallel blades (0.75 mm thickness, 6 mm wide). For grooves with FLAT side walls — piston-ring grooves, retaining-ring grooves, keyway grooves. The blade face sits flat against a flat surface.

Point micrometer: Conical anvils (30° angle, ~0.3 mm tip diameter). For POINTED or V-shaped features — thread roots, gear-tooth roots, ball-groove races, conical hole bottoms.

Rule of thumb:

  • If the measuring surfaces are FLAT and parallel → blade micrometer.
  • If the measuring surfaces are POINTED or conical → point micrometer.
  • If the measuring surfaces are FLAT/FLAT (e.g. the workpiece’s outer surfaces) → standard micrometer.

30° angle: a geometric compromise

The point micrometer’s conical anvils are typically 30° half-angle (60° total cone angle). This value is chosen as a compromise between:

  • A narrower angle (e.g. 15°): The tip fits into extremely narrow grooves. DRAWBACK: more fragile, wears faster, can chip under mechanical impact.
  • A wider angle (e.g. 60°): A more robust tip. DRAWBACK: does not fit into narrower features.

A 30° half-angle is the standard compromise — it fits into most thread depths, gear-tooth roots, and other conical features without being overly fragile.

Applications

Thread diameter measurement: PITCH diameter for both external and internal threads. Complements the wire method (three-wire method), which is more advanced.

Gear tooth-root diameter: Depth from the tooth tip down to the root of the gap. Critical for the gear’s mating characteristics.

Bearing groove diameter in shafts: Seat diameter for the rolling element. Typically Ø 25-100 mm range.

Spring groove diameter: Springs and retaining grooves in pistons.

Conical bore verification: During Morse taper manufacturing (I wrote about the science of Morse gauges earlier).

Punch-and-die verification: Stamping and mold manufacturing.

Milling tool inspection: Final wear on cutting tool tips.

Digital point micrometer 25-50 mm with 30° conical measuring faces IP65

The absolute encoder advantage

This specific Schut instrument has an ABSOLUTE encoder, not an incremental one. The difference:

  • Incremental encoder: Counts steps from a zero point. In the event of a power interruption it loses its position and must be re-calibrated at startup.
  • Absolute encoder: Reads its absolute position from a coded scale at every instant. Retains its position through a battery change without re-calibration.

For everyday workshop use, the absolute encoder eliminates the classic problem: “The battery died mid-measurement — I have to start over.” Absolute-encoder instruments continue with the correct value after a battery change.

25-50 mm measuring range — the go-to size

This model covers 25-50 mm. For full coverage of all features, additional sizes are needed:

  • 0-25 mm: for small grooves, micro-threads.
  • 25-50 mm: this model — the standard mid-range size.
  • 50-75 mm: larger gears, larger threads.
  • 75-100 mm: large shaft grooves.

Standard workshops typically have the 25-50 mm model as their starting point. Other sizes are purchased as needed.

IP65 for the workshop environment

The IP65 protection rating (dust-tight + protected against water jets) makes the instrument suitable for:

  • Direct use in a coolant environment (without first wiping down the object).
  • Quick rinsing after use.
  • Outdoor work with a risk of rain.
  • Dust-heavy environments (grinding workshops, sandblasting facilities).

What you get for your money

Schut digital point micrometer, 25-50 mm measuring range, 30° half-angle conical anvils (~0.3 mm tip diameter), digital LCD with 0.001 mm resolution, ±0.004 mm accuracy, absolute encoder that retains the zero point through a battery change, mm/inch switching, ABS/INC switching, preset function, ratchet stop for consistent contact force, hardened ground spindle and anvil, IP65 protection rating, with setting standard, ECONOMY LINE build quality. DKK 1,682.

A specialty tool for measuring gear tooth-root diameters, thread root diameters, bearing grooves, conical bottoms, and other pointed features that a flat micrometer cannot reach. Complementary to the blade micrometer (which measures flat-parallel grooves). Standard equipment in every precision workshop that does gear or thread work on a regular basis.

Read more: Digital point micrometer 25-50 mm in the shop →

More news

All news