Hoppa till innehåll
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%When the Hole Is 500 mm Deep, the Measuring Instrument Has to Keep UpSee why the drain is blocked before you tear up the floor: a camera on five meters of cableWhen two hands measure the same bore differently: How three measuring points eliminate operator errorWhen the Bore Has to Be Measured Right: How a Self-Centering Three-Point Micrometer Removes Operator UncertaintyThree measuring points give a bore diameter that doesn’t depend on who is measuringWhen the multimeter shows 90 volts on a disconnected cable: how to tell ghost voltage from the real thingRead the tolerance in seconds when the micrometer shows the deviation directlySmall holes are rarely measured correctly with two points: how three contact points give you a diameter result you can trustYour measurement is never better than the surface you measure againstHow to Measure Ground Resistance Without Disconnecting the Ground Connection and Without Ground StakesVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%When the Hole Is 500 mm Deep, the Measuring Instrument Has to Keep UpSee why the drain is blocked before you tear up the floor: a camera on five meters of cableWhen two hands measure the same bore differently: How three measuring points eliminate operator errorWhen the Bore Has to Be Measured Right: How a Self-Centering Three-Point Micrometer Removes Operator UncertaintyThree measuring points give a bore diameter that doesn’t depend on who is measuringWhen the multimeter shows 90 volts on a disconnected cable: how to tell ghost voltage from the real thingRead the tolerance in seconds when the micrometer shows the deviation directlySmall holes are rarely measured correctly with two points: how three contact points give you a diameter result you can trustYour measurement is never better than the surface you measure againstHow to Measure Ground Resistance Without Disconnecting the Ground Connection and Without Ground Stakes

When the Hole Is 500 mm Deep, the Measuring Instrument Has to Keep Up

Published November 20, 2026 at 18:19

A hydraulic cylinder leaks, a long bushing runs hot, or a bore on the machine was never checked all the way to the bottom. Most people who have worked with deep holes know the problem: the measurement at the opening looks fine, but the fault sits further down, where no ordinary measuring equipment can reach. This is where an instrument built for exactly that situation helps.

Schwenk measuring instrument with analog dial indicator for internal measurement, 12-20 mm, measuring depth 500 mm

What is it?

It is a two-point internal measuring instrument from Schwenk in the STANDARD LINE series, with a measuring range of 12 to 20 mm and a reach of 500 mm. The measuring head sits at the far end of a long probe rod, while the dial indicator sits at the handle, where you can read it. The head has two opposing contacts: a fixed reference and a spring-loaded probe. Both rest against the hole wall, and any variation in diameter shows up as a deflection on the dial indicator. The reference surfaces are hardened and ground, so the measurement is repeatable.

What problems does it solve?

The instrument does not just show a diameter, but the shape of the hole. As the head is guided through the bore, the deflection reveals taper, ovality and barrel shape. These are exactly the deviations that a caliper or a fixed plug gauge will not find, because they only occur further in. You get a picture of the entire bore instead of a single measuring point at the opening.

How to use it

You choose a setting ring with the nominal diameter and zero the dial indicator while the head is in the ring. The head is then guided through the hole, and you note the deflection at several positions along the length. The figures give you a simple measurement map of the bore, which you can compare from workpiece to workpiece or from before to after a repair.

Three typical applications

In hydraulics and maintenance, it is used to check wear in cylinders and valve blocks before deciding whether a component should be bored out, bushed or scrapped. In the machine shop industry, it is used for deep-hole inspection on machine tools, where a bore must hold its shape all the way through. In transmission and transport, it is used to assess wear in long bushings on conveyors and gearbox shafts, without the shaft having to come out of the machine.

Why it pays off

The price is considerably higher than for an ordinary hand measuring tool, but the comparison should not be made with a caliper. It should be made with the costs that arise when a deep bore is assessed incorrectly. A workpiece is scrapped because the fault is only discovered at assembly, or a cylinder is replaced even though it could have been repaired. Conversely, a component with a hidden taper may be installed and cause downtime later. With an instrument that measures directly at depth, you make the decision based on measured data and avoid both unnecessary replacement and repeated errors. Once the tool is in the workshop, a check takes only a few minutes.

See the instrument

If you regularly work with deep, slender bores, this is a tool that quickly becomes part of daily use. You can see specifications and accessories on the product page: Schwenk deep-hole gauge 12-20 mm, 500 mm depth.

Read more

More news

All news