Hoppa till innehåll
Free shipping over 3.738 DKK ex VAT! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%See why the drain is blocked before you tear up the floor: a camera on five meters of cableWhen two hands measure the same bore differently: How three measuring points eliminate operator errorWhen the Bore Has to Be Measured Right: How a Self-Centering Three-Point Micrometer Removes Operator UncertaintyThree measuring points give a bore diameter that doesn’t depend on who is measuringWhen the multimeter shows 90 volts on a disconnected cable: how to tell ghost voltage from the real thingRead the tolerance in seconds when the micrometer shows the deviation directlySmall holes are rarely measured correctly with two points: how three contact points give you a diameter result you can trustYour measurement is never better than the surface you measure againstHow to Measure Ground Resistance Without Disconnecting the Ground Connection and Without Ground StakesSurface temperature reads incorrectly if the emissivity doesn’t match the materialVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%See why the drain is blocked before you tear up the floor: a camera on five meters of cableWhen two hands measure the same bore differently: How three measuring points eliminate operator errorWhen the Bore Has to Be Measured Right: How a Self-Centering Three-Point Micrometer Removes Operator UncertaintyThree measuring points give a bore diameter that doesn’t depend on who is measuringWhen the multimeter shows 90 volts on a disconnected cable: how to tell ghost voltage from the real thingRead the tolerance in seconds when the micrometer shows the deviation directlySmall holes are rarely measured correctly with two points: how three contact points give you a diameter result you can trustYour measurement is never better than the surface you measure againstHow to Measure Ground Resistance Without Disconnecting the Ground Connection and Without Ground StakesSurface temperature reads incorrectly if the emissivity doesn’t match the material

Small holes are rarely measured correctly with two points: how three contact points give you a diameter result you can trust

Published 14 November 2026 at 11:02

Two colleagues measure the same bore and get two different numbers. One has tilted the instrument a few degrees, the other has hit the hole slightly off the diameter. With small holes of 6 to 12 mm there is almost no room to see what is going on, and the result depends on fingertip feel. It is a well-known problem on the workshop floor, and it costs time every time a measurement has to be repeated.

Digital indvendig tre-punkts mikrometer af Holtest-type IP65, Ø6-12 mm

What it is

This is a digital Holtest-type internal three-point micrometer, supplied as a set for hole measurement from Ø6 to Ø12 mm. Three carbide measuring faces are positioned 120° apart around the axis and are pressed against the hole wall simultaneously. This makes the instrument self-centering: it cannot sit crooked in the hole the way a two-point instrument can. The resolution is 0.001 mm, and the display can switch between mm and inches as well as between ABS and INC. It has reset/preset and automatic power-off, and the housing is IP65. The battery is a V357 or CR2032, and everything is supplied in an aluminum case.

What problems it solves

Telescoping gauges and calipers give a diameter that depends on how you hold them. A three-point micrometer gives a measured diameter that does not change between operators. The measuring range is covered without changing measuring anvils, so there is no risk of zeroing incorrectly or forgetting an anvil. The preset function means you set the instrument to the nominal diameter on a setting ring and then read the deviation in the hole.

When and why it is used

The method is used when the tolerance is tight and the hole is too small or too deep to reach with other instruments. You zero on the setting ring, insert the measuring head, turn until all three contacts are seated, and read the value. Check the zero point against the ring regularly, especially if the instrument is shared between several stations.

Three concrete situations

Machine shops: Bores in valve blocks, guide bushings and pump housings after boring or reaming. Here you can quickly see whether the hole is within tolerance before the part moves on.

Hydraulics and maintenance: Checking worn bushings and bearing seats during servicing. The IP65 enclosure withstands splashes of oil and cutting fluid, which otherwise quickly ruin an electronic instrument.

Food production and process plants: Checking small bores in dosing parts and stainless steel fittings, where a hole that is too large or oval causes leakage or uneven dosing.

Why it pays off

The price is not low, but the math is simple. Every scrapped or reworked precision part costs more than the minutes a reliable measurement takes. When the measurement does not depend on the operator, the number of repeated measurements falls, and disagreements between production and quality control become fewer. The carbide faces also last a long time, and the set in its case is easy to store and to calibrate at fixed intervals.

If you regularly have small, tight bores that need to be measured correctly the first time, you can see specifications and price on the product page.

Read more

More news

All news