Hoppa till innehåll
Free shipping over 3.738 DKK ex VAT! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%When the Bore Has to Be Measured Right: How a Self-Centering Three-Point Micrometer Removes Operator UncertaintyThree measuring points give a bore diameter that doesn’t depend on who is measuringWhen the multimeter shows 90 volts on a disconnected cable: how to tell ghost voltage from the real thingRead the tolerance in seconds when the micrometer shows the deviation directlySmall holes are rarely measured correctly with two points: how three contact points give you a diameter result you can trustYour measurement is never better than the surface you measure againstHow to Measure Ground Resistance Without Disconnecting the Ground Connection and Without Ground StakesSurface temperature reads incorrectly if the emissivity doesn’t match the materialWhen the Bore Looks Round but the Measurement Still Misleads: How Three Contact Points Give You a Number You Can TrustThe pipe wall looks intact from the outside, but how much steel is left inside?Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%When the Bore Has to Be Measured Right: How a Self-Centering Three-Point Micrometer Removes Operator UncertaintyThree measuring points give a bore diameter that doesn’t depend on who is measuringWhen the multimeter shows 90 volts on a disconnected cable: how to tell ghost voltage from the real thingRead the tolerance in seconds when the micrometer shows the deviation directlySmall holes are rarely measured correctly with two points: how three contact points give you a diameter result you can trustYour measurement is never better than the surface you measure againstHow to Measure Ground Resistance Without Disconnecting the Ground Connection and Without Ground StakesSurface temperature reads incorrectly if the emissivity doesn’t match the materialWhen the Bore Looks Round but the Measurement Still Misleads: How Three Contact Points Give You a Number You Can TrustThe pipe wall looks intact from the outside, but how much steel is left inside?

When the Bore Has to Be Measured Right: How a Self-Centering Three-Point Micrometer Removes Operator Uncertainty

Published 19 November 2026 at 00:27

Most people know it from the workshop: two people measure the same hole and get two different numbers. The instrument is the same, but one of them is tilted slightly, or the contact is not placed exactly across the center of the hole. For internal diameters, this is one of the most common sources of measurement error, and it is hard to trace afterwards.

Analog internal three-point micrometer of the Holtest type. Measuring range Ø60–70 mm. Scale division 0.005 mm. Self-centering. Carbide measuring faces. Set comes with setting rings and extension in a wooden case. Fast and accurate measurement of internal dimensions.

What it is

The analog three-point micrometer of the Holtest type is built for internal diameter measurement in the range Ø60–70 mm. Three carbide measuring faces are positioned 120° apart and are driven out toward the bore wall as the thimble is turned. The scale division is 0.005 mm, and the accuracy is specified as ±0.006 mm. The set comes with setting rings and an extension in a wooden case.

What problem it solves

Because the three contact points are evenly distributed around the axis, the instrument centers itself in the hole. The operator cannot tilt it away from the diameter in the same way as with a two-point instrument, and there is no need to search for the largest dimension by rocking it back and forth. The reading becomes more consistent from person to person, and that is exactly what a quality department needs.

How to use it

The instrument is zeroed on a setting ring with the nominal diameter. The measuring head is then inserted into the hole, the thimble is turned until all three faces are in contact, and the diameter is read. The ring and the workpiece should be at the same temperature before measuring, and the ring itself must be checked at regular intervals, typically every year, so that traceability is maintained.

Practical examples

Hydraulics and pneumatics. When inspecting incoming cylinder tubes and bushings in the Ø60–70 mm range, three-point measurement quickly gives a reliable figure for the bore diameter. The extension makes it possible to measure some distance inside the tube.

Machining. On a CNC lathe or milling machine, bearing seats and fitted bores can be checked between two operations. The deviation is seen immediately, so the tool offset can be corrected before the next workpiece is scrapped.

Pumps and valve housings. At manufacturers of process equipment, including for the food industry, sealing seats and bores must hold tight tolerances. Here, a fixed measuring method with a setting ring is easier to document than a free measurement with a caliper.

Why it pays off

The math is simple. A single scrapped housing or a cylinder that has to be reworked often costs more than the entire instrument. Then there is the time: when the measurement does not have to be repeated because two people disagreed, you save minutes at every inspection and arguments at every complaint. An instrument that gives the same answer regardless of the hand holding it also makes internal calibration and inspection work easier to plan.

For those who measure holes every day

If your bores are in the Ø60–70 mm range and you currently rely on a caliper or free feel, a self-centering three-point micrometer is a direct improvement in measurement reliability.

Read more

More news

All news