Hoppa till innehåll
Free shipping over 3.519 DKK ex VAT! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%Three measuring points give a bore diameter that doesn’t depend on who is measuringWhen the multimeter shows 90 volts on a disconnected cable: how to tell ghost voltage from the real thingRead the tolerance in seconds when the micrometer shows the deviation directlySmall holes are rarely measured correctly with two points: how three contact points give you a diameter result you can trustYour measurement is never better than the surface you measure againstHow to Measure Ground Resistance Without Disconnecting the Ground Connection and Without Ground StakesSurface temperature reads incorrectly if the emissivity doesn’t match the materialWhen the Bore Looks Round but the Measurement Still Misleads: How Three Contact Points Give You a Number You Can TrustThe pipe wall looks intact from the outside, but how much steel is left inside?Core product temperature can be documented even when nobody is watching the thermometerVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%Three measuring points give a bore diameter that doesn’t depend on who is measuringWhen the multimeter shows 90 volts on a disconnected cable: how to tell ghost voltage from the real thingRead the tolerance in seconds when the micrometer shows the deviation directlySmall holes are rarely measured correctly with two points: how three contact points give you a diameter result you can trustYour measurement is never better than the surface you measure againstHow to Measure Ground Resistance Without Disconnecting the Ground Connection and Without Ground StakesSurface temperature reads incorrectly if the emissivity doesn’t match the materialWhen the Bore Looks Round but the Measurement Still Misleads: How Three Contact Points Give You a Number You Can TrustThe pipe wall looks intact from the outside, but how much steel is left inside?Core product temperature can be documented even when nobody is watching the thermometer

Read the tolerance in seconds when the micrometer shows the deviation directly

Published 15 November 2026 at 09:08

Most people know it from an inspection station: a box with a couple of hundred turned pins, an operator with an ordinary micrometer, and a tolerance of a few hundredths of a millimetre. Each part requires a reading on the scale and thimble, a mental calculation and an assessment. After an hour of work the readings start to drift, and borderline cases are judged differently from person to person.

Tolerance micrometer with fine dial indicator IP54, 0-25 mm, dial accuracy ±0.001 mm, graduation 0.001 mm, dial measuring range ±0.04 mm, measuring force 5-10 N, adjustable tolerance markers, carbide measuring faces Ø10 mm, IP54, delivered in aluminium case

A micrometer with a built-in dial indicator

A tolerance micrometer is a C-frame micrometer with a fine dial indicator fitted in place of the ordinary fixed anvil. This instrument has a measuring range of 0-25 mm, and the dial has a graduation of 0.001 mm with a reading range of ±0.04 mm. The dial accuracy is specified as ±0.001 mm. The measuring faces are carbide with a diameter of 10 mm, and the measuring force is 5-10 N. The frame is thermally insulated, so hand warmth affects the measurement less, and the instrument has an IP54 rating and is delivered in an aluminium case.

What problem does it solve

You set the micrometer to the nominal size with a gauge block and lock the spindle. Then you set the adjustable tolerance markers on the dial to match the upper and lower limits. The rest is simple: if the pointer lies within the markers, the part is approved. There is no subtraction and no interpretation of the scale. This removes the biggest source of error in serial inspection, namely the reading, and makes the result independent of who is standing at the bench.

When it is used

The instrument is for situations where many parts must be measured against the same dimension. Typically this is sample inspection at the machine, where the operator needs to know whether the tool is wearing before the parts go out of tolerance. Displaying the deviation makes it easy to spot a trend long before the first rejected part.

Three concrete examples

In the machine shop industry it is used for turned shafts and pins in a series where the diameter must stay within a few hundredths of a millimetre. The operator can measure and adjust the tool offset directly from the dial deflection.

In electronics production it can be used to check the thickness of spacers, contact pins and pressed parts, where small deviations cause poor contact or assembly problems.

In sanitary installations and fittings production it is used for brass spindles, sealing washers and compression fitting parts, where the fit determines whether the joint is tight.

Why it pays off

The time saving comes from each measurement becoming a quick glance at the dial instead of a reading and a calculation. Sorting becomes consistent from shift to shift, and fewer parts are scrapped or rejected by the customer because of misreading. The ratchet and the defined measuring force of 5-10 N also mean that two people get the same result on the same part, which reduces discussions about the measurement. For a department with ongoing serial inspection, this is typically one of the quickest ways to improve both speed and reliability without investing in automatic measuring equipment.

See the full specifications and order the tolerance micrometer from us.

Read more

More news

All news