Hoppa till innehåll
Free shipping over 3.000 DKK ex VAT! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%Three measuring points give a bore diameter that doesn’t depend on who is measuringWhen the multimeter shows 90 volts on a disconnected cable: how to tell ghost voltage from the real thingRead the tolerance in seconds when the micrometer shows the deviation directlySmall holes are rarely measured correctly with two points: how three contact points give you a diameter result you can trustYour measurement is never better than the surface you measure againstHow to Measure Ground Resistance Without Disconnecting the Ground Connection and Without Ground StakesSurface temperature reads incorrectly if the emissivity doesn’t match the materialWhen the Bore Looks Round but the Measurement Still Misleads: How Three Contact Points Give You a Number You Can TrustThe pipe wall looks intact from the outside, but how much steel is left inside?Core product temperature can be documented even when nobody is watching the thermometerVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%Three measuring points give a bore diameter that doesn’t depend on who is measuringWhen the multimeter shows 90 volts on a disconnected cable: how to tell ghost voltage from the real thingRead the tolerance in seconds when the micrometer shows the deviation directlySmall holes are rarely measured correctly with two points: how three contact points give you a diameter result you can trustYour measurement is never better than the surface you measure againstHow to Measure Ground Resistance Without Disconnecting the Ground Connection and Without Ground StakesSurface temperature reads incorrectly if the emissivity doesn’t match the materialWhen the Bore Looks Round but the Measurement Still Misleads: How Three Contact Points Give You a Number You Can TrustThe pipe wall looks intact from the outside, but how much steel is left inside?Core product temperature can be documented even when nobody is watching the thermometer

Why 112 Blocks Are Enough for Almost Any Measurement, and Why They Stick Together

Published August 24, 2026 at 01:59

A set of gauge blocks looks like a box full of nearly identical steel blocks. It isn’t. It’s a number system, where each individual size is chosen so that a handful of blocks stacked together can hit practically any target dimension in steps of one thousandth of a millimeter.

Steel gauge blocks in set M112 class 2 per ISO 3650 in wooden case

What it is

A set of steel gauge blocks M112, class 2, per ISO 3650.

  • 112 blocks, including the thousandths series 1.001 to 1.009 mm in steps of 0.001 mm
  • Hardness 63-65 HRC
  • Coefficient of expansion (11.5 ±1) · 10⁻⁶ per degree
  • Cross-section 30 x 9 mm for 0.5 to 10 mm, 35 x 9 mm above 10 mm
  • Supplied in a wooden case with the manufacturer’s calibration protocol

How to build a dimension

The rule is to take the last decimal first. To build 47.623 mm, you start with 1.003 to clear the thousandth, then 1.12 for the hundredth, then 5.5, and finally 40. Four blocks, and the sum is exact. With this method, the number of blocks in the stack almost always comes out to three to five — and that’s no coincidence, but precisely why the set’s sizes are chosen the way they are.

The blocks are not held together by magnetism. They are wrung — pressed against each other with light pressure and a twist — and afterward they adhere so strongly that you can lift the entire stack by the top block. The surfaces are so flat and smooth that there is practically no air between them, and the thin layer that remains is so thin that the stack’s length is treated as the pure sum of the blocks. A properly wrung stack behaves like a single piece of steel.

Class 2 and the calibration protocol go together. The class states how much deviation an individual block may have. The protocol states how large it actually is, block by block. That difference is what makes a workshop set usable for fine work: if you need more than the class guarantees, you can factor in the known deviation instead of buying a more expensive class.

The coefficient of expansion is stated on the set for a reason. Gauge blocks are defined at 20 degrees. A 100 mm stack changes by about 5.75 µm at a deviation of five degrees — more than the entire tolerance on many of the dimensions the stack is used to check. That’s why you let the blocks equalize to temperature before use, and why you handle them as little and as briefly as possible: a hand is roughly seventeen degrees warmer than the measurement room.

Three typical applications

  • Checking measuring equipment: setting and verifying micrometers, dial indicators, and internal measuring instruments against a known dimension.
  • Machine setup: setting stops, heights, and distances where a known dimension is faster than a measurement.
  • Toolmaking: as a standard when manufacturing and checking gauges, fixtures, and templates.

Why it pays off

A set of gauge blocks isn’t a measuring instrument — it’s what all the other instruments are measured against. Without an independent reference, you can only establish that two instruments disagree, not which of them is right. With a set in the drawer, the question is settled in a minute, by whoever is holding the instrument, instead of dragging on as a dispute between two shifts or between supplier and customer.

And because the blocks are hardened to 63-65 HRC, they last for decades with ordinary care. It’s one of the few purchases in a workshop where the person who buys it is rarely the last one to use it.

Read more about steel gauge block sets M112 →

More news

All news