Hoppa till innehåll
Free shipping over 3.738 DKK ex VAT! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%Three measuring points give a bore diameter that doesn’t depend on who is measuringWhen the multimeter shows 90 volts on a disconnected cable: how to tell ghost voltage from the real thingRead the tolerance in seconds when the micrometer shows the deviation directlySmall holes are rarely measured correctly with two points: how three contact points give you a diameter result you can trustYour measurement is never better than the surface you measure againstHow to Measure Ground Resistance Without Disconnecting the Ground Connection and Without Ground StakesSurface temperature reads incorrectly if the emissivity doesn’t match the materialWhen the Bore Looks Round but the Measurement Still Misleads: How Three Contact Points Give You a Number You Can TrustThe pipe wall looks intact from the outside, but how much steel is left inside?Core product temperature can be documented even when nobody is watching the thermometerVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%Three measuring points give a bore diameter that doesn’t depend on who is measuringWhen the multimeter shows 90 volts on a disconnected cable: how to tell ghost voltage from the real thingRead the tolerance in seconds when the micrometer shows the deviation directlySmall holes are rarely measured correctly with two points: how three contact points give you a diameter result you can trustYour measurement is never better than the surface you measure againstHow to Measure Ground Resistance Without Disconnecting the Ground Connection and Without Ground StakesSurface temperature reads incorrectly if the emissivity doesn’t match the materialWhen the Bore Looks Round but the Measurement Still Misleads: How Three Contact Points Give You a Number You Can TrustThe pipe wall looks intact from the outside, but how much steel is left inside?Core product temperature can be documented even when nobody is watching the thermometer

The indicator doesn’t determine whether the item is broken, but whether someone needs to check it

Published August 27, 2026 at 17:51

Transport damage is almost always discovered too late. The box is signed for, brought into the warehouse, opened an hour or a week later — and then the question arises: did it happen in transit, or did it happen here? By that point there’s no documentation, only two parties who are both convinced they’re right.

A shock indicator on the outside of the packaging moves that question to the only moment it can actually be settled: while the driver is still standing there.

Drop-N-Tell stoedindikator 25G til overvaagning af haandtering under transport

What it is

Drop-N-Tell shock indicator, 25 G, normal sensitivity, 100 pcs.

  • Self-adhesive — peel off the backing and attach the indicator to the packaging
  • The recipient can see whether the package has taken a hit, without opening it
  • Resettable and reusable up to 25 times

25 G is a choice, not a classification

The threshold needs to match the goods and their normal handling. Set it too low and the indicator triggers on every forklift bump and every time the box is set down — and an indicator that has always triggered carries exactly as much information as one that never does: none. After a few weeks, nobody bothers checking them anymore.

Set it too high and it lets handling that could actually damage the contents pass through without flagging anything. Choosing the threshold is therefore the real product decision, and it depends on two things: what the item can withstand, and what it’s normally subjected to along the way.

One bit of information — and that’s the point

The indicator doesn’t tell you how hard, when, or how many times. It tells you the threshold was exceeded at some point. That’s the same kind of information a temperature logger with a green and red LED gives you: a yes or no, read in a few seconds without any equipment.

And just as with that, it’s enough for the decision that needs to be made on receipt. If you need to know more — how hard, at what point on the route — electronic recorders exist that log acceleration. They cost significantly more, and they’re used where the answer needs to hold up in a dispute, not just in a sorting decision.

The important limitation

The indicator is on the packaging, not on the product. That means it describes what the box has been exposed to — not what the contents have withstood.

A triggered indicator is therefore not proof that the product is defective, and an untriggered one is not proof that it’s intact. It’s a prompt: to open and inspect before signing, and to note the reservation on the waybill. Used as a verdict, it will sooner or later become the basis for a wrongful rejection — and then you’ve traded one dispute for another.

Resettable or not

Being reusable up to 25 times changes the calculation for closed loops. If you ship in your own boxes or on returnable packaging, the indicator travels back with it and is used again. For one-way shipments, on the other hand, it makes no difference — there, the unit price is all that matters, and the indicator is never seen again.

Three typical applications

  • Sensitive equipment: instruments, electronics and machine parts where damage isn’t visible from the outside.
  • Returnable packaging: fixed loops where the indicator can be reused.
  • Supplier dialogue: documenting how goods are actually handled on a given route.

Why it pays off

The cost of transport damage is rarely just the product itself. It’s the time spent determining who’s responsible, and that negotiation is expensive precisely because there’s no data.

A label on the outside costs a few kroner per shipment and makes the question concrete at the point of delivery instead of a matter of principle afterward. And there’s a side benefit that’s often the biggest one: when both the sender and the carrier know that handling is visible, handling changes.

Read more about the Drop-N-Tell shock indicator 25 G →

More news

All news