Hoppa till innehåll
Free shipping over 3.738 DKK ex VAT! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%See why the drain is blocked before you tear up the floor: a camera on five meters of cableWhen two hands measure the same bore differently: How three measuring points eliminate operator errorWhen the Bore Has to Be Measured Right: How a Self-Centering Three-Point Micrometer Removes Operator UncertaintyThree measuring points give a bore diameter that doesn’t depend on who is measuringWhen the multimeter shows 90 volts on a disconnected cable: how to tell ghost voltage from the real thingRead the tolerance in seconds when the micrometer shows the deviation directlySmall holes are rarely measured correctly with two points: how three contact points give you a diameter result you can trustYour measurement is never better than the surface you measure againstHow to Measure Ground Resistance Without Disconnecting the Ground Connection and Without Ground StakesSurface temperature reads incorrectly if the emissivity doesn’t match the materialVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%See why the drain is blocked before you tear up the floor: a camera on five meters of cableWhen two hands measure the same bore differently: How three measuring points eliminate operator errorWhen the Bore Has to Be Measured Right: How a Self-Centering Three-Point Micrometer Removes Operator UncertaintyThree measuring points give a bore diameter that doesn’t depend on who is measuringWhen the multimeter shows 90 volts on a disconnected cable: how to tell ghost voltage from the real thingRead the tolerance in seconds when the micrometer shows the deviation directlySmall holes are rarely measured correctly with two points: how three contact points give you a diameter result you can trustYour measurement is never better than the surface you measure againstHow to Measure Ground Resistance Without Disconnecting the Ground Connection and Without Ground StakesSurface temperature reads incorrectly if the emissivity doesn’t match the material
Item number 28-300B

Digital pocket thermometer with rubber protection, -40 to 150C.

131 DKK

In stock

The 300B Digital Temperature Probe features a 1.5 mm thin tip for fast response and comes with a protective rubber boot for extra protection.

Request a quote 28-300B

Volume discount: 5 pcs: 2% · 10 pcs: 3% · 25 pcs: 5%

Category:

Other models in the series 16

Description

The 300B Digital Temperature Probe features a 1.5 mm thin tip for rapid response and comes with a protective rubber boot for extra protection. With large digits, it is an easy-to-read and easy-to-use thermometer for quick checks when preparing a variety of foods.

The temperature probe has a hold button that allows the user to freeze the digital reading on the screen while noting a measurement.

The 300B digital temperature probe is also waterproof.

The 300B digital temperature probe with boot is a basic reduced (thin) tip thermometer with Biocote Antimicrobial protection. The 300B is slim and lightweight, making it perfect for slipping into shirt, trouser, or apron pockets between uses. It has a 127mm / 5″ long stem and a 1.5 mm / 0.6″ diameter from the tip, making it suitable for probing thinner foods. The 300B digital temperature probe is field calibratable and has switchable °F/°C temperature scales/ranges, a data hold function, and a low battery indicator. You can either use ON/OFF to save battery life or let the unit switch off automatically after a short period. This digital pocket thermometer includes a protective pouch with a pocket clip and a battery.

The 300B is also available without the rubber boot, click here.


Field Calibration Procedures

1. The 300B is only calibratable in an ice slurry – 60 percent crushed ice to 40 percent tap water – or a water bath. Do not attempt to calibrate in any other way

2. Immerse the thermometer shaft to at least half its length in the ice slurry

3. Wait until the reading stabilizes (typically within ±2° of 32 °F or ±1° of 0 °C)

4. Press and hold the CAL button for 8 seconds to initiate calibration

5. Calibration is displayed for two seconds, and calibration at 0 °C / 32 °F is complete

6. Remove the thermometer from the ice water and continue measuring

Note: CAL is displayed whenever D-H is pressed for 8 seconds, but the thermometer will not calibrate unless the tip is inserted into ice water


°F/°C Switchable

The 300B digital temperature probe has temperature scales/ranges that can be switched to °F/°C. With the thermometer turned OFF, press and hold ON/OFF. Release when the desired scale is displayed.

Note: This is the procedure for all digital pocket thermometers that do not have a °F/°C scale button.

Additional information
Product type

PDF (6)
Reviews (0)

There are no reviews yet.

Be the first to review

Your e-mail address is not published.

Your rating *